For Canadian residents wanting to purchase, contact Aztech Armory at info@aztecharmory.com
For red dot to base compatibility, go here
New! MADDMACS SHIELD RMS/rms-c CENTER BASE #MPTSCB
The new MaddMacs Center Base 2.0 for the Shield RMS/RMS-C is now available! Now you can mount the smallest red dot to the lowest base onto your Ruger® MK Series pistol. Mounts over the ejection port using the low profile T10 Torx screws. Made from 6061 aluminum with an exact footprint of Shield RMS/RMS-C, this is the thinnest base on market. You will not find a base specifically designed for this red dot to mount to your Ruger® MK Series anywhere else but here! And yes, you can see your front sight through the red dot.
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
T15 Torx M4 x 0.70 screws included
Will fit on all Ruger® MK Series pistols
Will also fit the Tactical Solutions Pac Lite™ upper.
$57.95
***The option to choose the RMS or RMS-C after clicking Buy Now***
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
T15 Torx M4 x 0.70 screws included
Will fit on all Ruger® MK Series pistols
Will also fit the Tactical Solutions Pac Lite™ upper.
$57.95
***The option to choose the RMS or RMS-C after clicking Buy Now***
NEW! MADDMACS SHIELD RMS/rms-c DT BASE #MPTSDT
The new MaddMacs Dovetail Base 2.0 for the Shield RMS/RMS-C is now available! Now you can mount the smallest red dotto the lowest base onto your Ruger® MK Series pistol. Mount secures to your pistol in the rear sight dovetail and first scope base screw hole with the low profile T10 Torx screws. Made from 6061 aluminum with an exact footprint of Shield RMS/RMS-C, this is the thinnest base on market. You will not find a base specifically designed for this red dot to mount to your Ruger® MK Series anywhere else but here! And yes, you can see your front sight through the red dot.
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
T15 Torx M4 x 0.70 screws included
Will fit on all Ruger® MK Series pistols
$89.95
***The option to choose the RMS or RMS-C after clicking Buy Now***
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
T15 Torx M4 x 0.70 screws included
Will fit on all Ruger® MK Series pistols
$89.95
***The option to choose the RMS or RMS-C after clicking Buy Now***
maddmacs center Base 2.0
The new MaddMacs Center Base 2.0 for the Ruger® MK Series pistols is a re-designed version of the original MaddMacs Center Base with more features. First, the 2.0 has alignment pins machined into the base to accept all Burris FastFire™ III and Vortex Venom® red dots. This will take all the guess work out aligning your red dot to the base and will help keep it secure. As with original, the 2.0 is machined to perfectly fit flush with the FFIII™ or Venom® but has been shortened some in it's overall length and still undercut for the ejection port. The T10 Torx screws used for mounting the base have been machined with a thinner head allowing the the 2.0 to be thinnest base on the market. The new 2.0 mounts your red dot .0825" above the receiver!
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
Will fit on all Ruger® MK Series pistols
Will also fit the Tactical Solutions Pac Lite™ upper.
(Engraving will be located on the top)
$54.95
Maddmacs DeltaPoint DT Base 2.0 #mptdpdb5
The new MaddMacs Deltapoint Pro Dovetail Base 2.0 for the Ruger® MK Series pistols is a re-designed version of the original MaddMacs DT Base with more features. First, the 2.0 has alignment pins machined into the base to accept the Luepold® Deltapoint Pro™ red dots. This will take all the guess work out aligning your red dot to the base and will help keep it secure. As with original, the 2.0 is machined to perfectly fit flush with the Deltapoint Pro™ but has been shortened some in it's overall length and still undercut for the ejection port. Mount secures to your pistol in the rear sight dovetail and first scope base screw hole. The T10 Torx screws used for mounting the base have been machined with a thinner head allowing the the 2.0 to be thinnest base on the market. The new 2.0 mounts your red dot .0825" above the receiver!
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
Will fit on all Ruger® MK Series pistols
$85.95
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
Will fit on all Ruger® MK Series pistols
$85.95
maddmacs viper center base 2.0 #mptvvcb2.0
zThe new MaddMacs Viper Center Base 2.0 for the Ruger® MK Series pistols is a re-designed version of the original MaddMacs Viper Center Base with more features. First, the 2.0 has alignment pins machined into the base to accept the Vortex Viper® red dots. This will take all the guess work out aligning your red dot to the base and will help keep it secure. As with original, the 2.0 is machined to perfectly fit flush with the Viper but has been shortened some in it's overall length and still undercut for the ejection port. The T10 Torx screws used for mounting the base have been machined with a thinner head allowing the the 2.0 to be thinnest base on the market. The new 2.0 mounts your red dot .0825" above the receiver!
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
Will fit on all Ruger® MK Series pistols
Will also fit the Tactical Solutions Pac Lite™ upper.
$66.95
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
Will fit on all Ruger® MK Series pistols
Will also fit the Tactical Solutions Pac Lite™ upper.
$66.95
maddmacs rmr dt Base 2.0 #MPTRMRDT2.0
The new MaddMacs RMR Dovetail Base 2.0 for the Ruger® MK Series pistols is a re-designed version of the original MaddMacs RMR DT Base with more features. First, the 2.0 has alignment pins machined into the base to accept the Trijicon® RMR red dots. This will take all the guess work out aligning your red dot to the base and will help keep it secure. As with original, the 2.0 is machined to perfectly fit flush with the RMR™ but has been shortened some in it's overall length and still undercut for the ejection port. Mount secures to your pistol in the rear sight dovetail and first scope base screw hole. The T10 Torx screws used for mounting the base have been machined with a thinner head allowing the the 2.0 to be thinnest base on the market. The new 2.0 mounts your red dot .0825" above the receiver!
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
Will fit on all Ruger® MK Series pistols
$94.95
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
Will fit on all Ruger® MK Series pistols
$94.95
MaddMacs dp pro Center Base 2.0 #MPTDPCB2.0
The new MaddMacs DP Pro Center Base 2.0 for the Ruger® MK Series pistols is a re-designed version of the original MaddMacs DeltaPoint Pro Center Base with more features. First, the 2.0 has alignment pins machined into the base to accept Leupold® DeltaPoint Pro red dots. This will take all the guess work out aligning your red dot to the base and will help keep it secure. As with original, the 2.0 is machined to perfectly fit flush with the DeltaPoint Pro but has been shortened some in it's overall length and still undercut for the ejection port. The T10 Torx screws used for mounting the base have been machined with a thinner head allowing the the 2.0 to be thinnest base on the market. The new 2.0 mounts your red dot .0825" above the receiver!
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
Will fit on all Ruger® MK Series pistols
Will also fit the Tactical Solutions Pac Lite™ upper.
$59.95
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
Will fit on all Ruger® MK Series pistols
Will also fit the Tactical Solutions Pac Lite™ upper.
$59.95
MaddMacs RMR Center Base 2.0 #MPTRMRCB2.0
The new MaddMacs RMR Center Base 2.0 for the Ruger® MK Series pistols is a re-designed version of the original MaddMacs RMR Center Base with more features. First, the 2.0 has alignment pins machined into the base to accept all Trijicon® RMR red dots. This will take all the guess work out aligning your red dot to the base and will help keep it secure. As with original, the 2.0 is machined to perfectly fit flush with the RMR but has been shortened some in it's overall length and still undercut for the ejection port. The T10 Torx screws used for mounting the base have been machined with a thinner head allowing the the 2.0 to be thinnest base on the market. The new 2.0 mounts your red dot .0825" above the receiver!
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
Will fit on all Ruger® MK Series pistols
Will also fit the Tactical Solutions Pac Lite™ upper.
$64.95
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
Will fit on all Ruger® MK Series pistols
Will also fit the Tactical Solutions Pac Lite™ upper.
$64.95
maddmacs DT Base 2.0 #MPTDTB2.0
|
|
The new MaddMacs Dovetail Base 2.0 for the Ruger® MK Series pistols is a re-designed version of the original MaddMacs DT Base with more features. First, the 2.0 has alignment pins machined into the base to accept all Burris FastFire™ III and Vortex Venom® red dots. This will take all the guess work out aligning your red dot to the base and will help keep it secure. As with original, the 2.0 is machined to perfectly fit flush with the FFIII™ or Venom® but has been shortened some in it's overall length and still undercut for the ejection port. Mount secures to your pistol in the rear sight dovetail and first scope base screw hole. The T10 Torx screws used for mounting the base have been machined with a thinner head allowing the the 2.0 to be thinnest base on the market. The new 2.0 mounts your red dot .0825" above the receiver!
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
Will fit on all Ruger® MK Series pistols
$91.95
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
Will fit on all Ruger® MK Series pistols
$91.95
maddmacs RTS2 center Base 2.0 #mptrts2cb2.0
The new MaddMacs RTS2 Center Base 2.0 for the Ruger® MK Series pistols is a re-designed version of the original MaddMacs RTS2 Center Base with more features. First, the 2.0 has alignment pins machined into the base to accept the C-More RTS2 red dot. This will take all the guess work out aligning your red dot to the base and will help keep it secure. As with original, the 2.0 is machined to perfectly fit flush with the RTS2 but has been shortened some in it's overall length and still undercut for the ejection port. The T10 Torx screws used for mounting the base have been machined with a thinner head allowing the the 2.0 to be thinnest base on the market. The new 2.0 mounts your red dot .0825" above the receiver!
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
Will fit on all Ruger® MK Series pistols
Will also fit the Tactical Solutions Pac Lite™ upper.
$58.95
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
Will fit on all Ruger® MK Series pistols
Will also fit the Tactical Solutions Pac Lite™ upper.
$58.95
Positive Stop Plug Screws #MPTPSPSB
6-48 plug screws for scope base holes. Positive stop screws have a rounded top that blends right in with your 22/45™ and 22/45 LITE® upper. Oversized head will not allow the screws to be threaded too deep .
*** Will NOT fit the front sight screw hole of MKII or MKIII***
Will fit front sight screw hole of the new MKIV
Quantities of 1, 2 or 3 screws per pack available after clicking Buy Now
Color: Blued
Starting at $6.50
*** Will NOT fit the front sight screw hole of MKII or MKIII***
Will fit front sight screw hole of the new MKIV
Quantities of 1, 2 or 3 screws per pack available after clicking Buy Now
Color: Blued
Starting at $6.50
SightMark mini shot m-spec maddmacs center Base #mptsmmscB
MaddMacs exclusive design for the SightMark Mini Shot M-Spec red dot. Mount secures to your MK Series pistol in the first two scope base holes. Extremely low, mounting the Mini Shot less than .12" high. That's 3 times lower than the picatinny base and rail. Undercut for ejection port. Easy to install. Made from 6061 aluminum and DuraCoated in Black Oxide.
Will fit all MKIII™ and MKIV ™pistols
Will also fit the Tactical Solutions Pac Lite™ upper.
Comes with installation instructions and mounting hardware
$66.95
Will fit all MKIII™ and MKIV ™pistols
Will also fit the Tactical Solutions Pac Lite™ upper.
Comes with installation instructions and mounting hardware
$66.95
SightMark mini shot m-spec maddmacs DOVETAIL Base #mptsmmsDTB
MaddMacs exclusive design for the SightMark Mini Shot M-Spec. Mount secures to your pistol in the rear sight dovetail and first scope base screw hole. Extremely low, mounting the Mini Shot less than .12" high. That's 3 times lower than the picatinny base and rail. Easy to install. Made from 6061 aluminum and DuraCoated in Black Oxide. Fits all Ruger MKIII™ and MKIV™ Series pistols.
Comes with installation instructions and mounting hardware
$109.95
Comes with installation instructions and mounting hardware
$109.95
NIKON® P-TACTICAL SPUR maddmacs CENTER BASE #MPTNSCB2
MaddMacs exclusive design for the Nikon® P-TACTICAL Spur red dot. Mount secures to your MK Series pistol in the first two scope base holes. Extremely low, mounting the Spur less than .12" high. That's 3 times lower than the picatinny base and rail. Undercut for ejection port. Easy to install. Made from 6061 aluminum and DuraCoated in Black Oxide.
Will fit all Ruger® MK Series pistols
Will also fit the Tactical Solutions Pac Lite™ upper.
Comes with installation instructions and hardware
$68.95
Will fit all Ruger® MK Series pistols
Will also fit the Tactical Solutions Pac Lite™ upper.
Comes with installation instructions and hardware
$68.95
nikon® p-tactical spur maddmacs dovetail Base #mptnsdb1
MaddMacs exclusive design for the Nikon® P-TACTICAL Spur. Mount secures to your pistol in the rear sight dovetail and first scope base screw hole. Extremely low, mounting the Spur less than .12" high. That's 3 times lower than the picatinny base and rail. Easy to install. Made from 6061 aluminum and DuraCoated in Black Oxide.Fits all Ruger Will fit all Ruger® MK Series pistols
Comes with installation instructions and hardware
$119.95
Comes with installation instructions and hardware
$119.95
new! maddmacs rts2 dt 2.0 Base #MPTRTSDT2.0
The new MaddMacs RTS2 Dovetail Base 2.0 for the Ruger® MK Series pistols is a re-designed version of the original MaddMacs DT Base with more features. First, the 2.0 has alignment pins machined into the base to accept the C-More RTS2 red dots. This will take all the guess work out aligning your red dot to the base and will help keep it secure. As with original, the 2.0 is machined to perfectly fit flush with the RTS2 but has been shortened some in it's overall length and still undercut for the ejection port. Mount secures to your pistol in the rear sight dovetail and first scope base screw hole. The T10 Torx screws used for mounting the base have been machined with a thinner head allowing the the 2.0 to be thinnest base on the market. The new 2.0 mounts your red dot .0825" above the receiver!
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
Will fit on all Ruger® MK Series pistols
$92.95
Made from 6061-T6 aluminum and DuraCoated in Black Oxide.
Easy to install (instructions and hardware included)
Will fit on all Ruger® MK Series pistols
$92.95
Maddmacs short rail #mptspr11
This picatinny rail is designed exclusively for the Ruger® MK series of pistols. Shorter than any other rail on the market measuring only 3". This rail WILL NOT hang over the receiver of your MK Series Target/Bull barrel pistol. Mount your favorite mini red dot on this thinner rail to eliminate the factory Weaver base that came with your gun. Comes with three 6-48 Torx screws and key.
***Will also fit the Tactical Solutions PacLite upper***
Color choice after selecting Buy Now
$41.95
***Will also fit the Tactical Solutions PacLite upper***
Color choice after selecting Buy Now
$41.95
maddmacs Accessory rail #mptar7
Ruger® MK Series Target model Accessory Rail manufactured by MaddMacs. Measuring only 2.55" long for mounting on the underside of your Ruger® Target Model pistol. This rail will allow you to mount your favorite laser or light on the underside of your pistol. Will fit only those barrels measuring .875" OD (Bull Barrel)
Comes with mounting hardware and key.
***Requires drilling and tapping of your barrel***
$41.95
Comes with mounting hardware and key.
***Requires drilling and tapping of your barrel***
$41.95
Drill & Tap for accessory rail #mptari2
Send your upper to MaddMacs for the drilling and tapping service for the above accessory rail. Cost includes rail and installation
Ship upper via UPS ONLY:
MaddMacs Precision Tactical, LLC
2401 Beaverdale Rd NE
Dalton, GA 30721
***Include a copy of the New Order Email***
$85.00
Ship upper via UPS ONLY:
MaddMacs Precision Tactical, LLC
2401 Beaverdale Rd NE
Dalton, GA 30721
***Include a copy of the New Order Email***
$85.00
dovetail parts kit #mptdtpk1
Replacement parts for the MaddMacs Dovetail bases. Will fit the DeltaPoint Pro, Trijicon RMR, Vortex Venom® and Burris FastFire™ III dovetail bases.
Includes the threaded dovetail, 6-48 Torx screws and key.
***Please note - this dovetail may NOT fit older bases that do not have MaddMacs Precision Tactical engraved in the top***
$18.95
Includes the threaded dovetail, 6-48 Torx screws and key.
***Please note - this dovetail may NOT fit older bases that do not have MaddMacs Precision Tactical engraved in the top***
$18.95
Competition frame upgrade #MPTCF01
A complete upgrade to your supplied frame. Send your complete MKIII™ or MKIV™ 22/45 lower (including mainspring assembly) to MaddMacs to have the VC Target Trigger job , MaddMacs Extended Mag Release and *MaddMacs "Madd-Dawg" Slingshot Mod installed for only $225! This is a $275 value! Here's what you will have when completed:
1. A trigger pull of less than 2lbs with both pre-travel and over-travel adjustments and that annoying magazine disconnect removed.
2. An extended mag button for easy mag drops.
3. A slingshot modification to avoid using the bolt release to chamber that fresh round.
Return shipping not included
* MKIV™ will not get the sling shot mod but will be upgraded to the VC Target Trigger
Ship your complete lower (including mainspring assembly) via USPS Priority Mail too:
MaddMacs Precision Tactical, LLC
2401 Beaverdale Rd NE
Dalton, GA 30721
Include a copy of the order receipt you received by email
#MPTCF01 $225.00
"Madd-Dawg" Slingshot Mod #MPTMDSM
The new slingshot bolt release for the Ruger® 22/45 MKIII™. No more fumbling with the bolt release after loading a new mag. Just pull back the bolt and let go!
**Some Gunsmithing Required**
$39.95
**Some Gunsmithing Required**
$39.95
Reduced Hammer Spring #MPTRHS
Reduced hammer spring to lighten the pull weight of the Ruger® MKIII 22/45™ and 22/45 LITE®. Installing this spring into the mainspring assembly can reduce the weight of your factory trigger pull by a half pound.
**Some gunsmithing required**
$9.95
**Some gunsmithing required**
$9.95
Ruger® MKIII 22/45™ Factory Magazine #MPT2245RM
Ruger® MKIII 22/45™ factory magazine. Fits all MKIII 22/45™s and 22/45 LITE®s.
Limited quantities.
$30.95
Limited quantities.
$30.95
MaddMacs 22/45™ Hammer Bushing #MPTSHB
Newly Redesigned! Stainless Steel hammer bushing to replace the factory magazine disconnect and bushing. Will allow for smooth magazine drop.
**Some Gunsmithing Required**
$24.95
**Some Gunsmithing Required**
$24.95
MaddMacs 22/45™ Extended Mag Release Button #2245EMB1
Oversized magazine release button. Allows for easier reach to eject 22/45™ mag. Threaded at 4-40. Compatible with the MKIII™ and MKIV™ series 22/45™s.
Black Oxide.
**Gunsmithing installation required** NO returns excepted
Magazine release NOT included. Button only.
$18.95
Black Oxide.
**Gunsmithing installation required** NO returns excepted
Magazine release NOT included. Button only.
$18.95
Installation #2245EMB1I
MaddMacs can install the extended mag button to your magazine release. The cost includes installation fee and button. Ship your mag release to:
MaddMacs Precision Tactical, LLC
2401 Beaverdale Rd NE
Dalton, GA 30721
Include a copy of the order receipt you received by email
You can also send your frame (lower) to have the mag release removed then re-installed once button is installed. Additional cost will apply.
$50.00
(Price does NOT include return shipping)
**NOTE** This is a permanent modification to your mag release. Button will be permanent. View photo of installed extended magazine release below.
MaddMacs can install the extended mag button to your magazine release. The cost includes installation fee and button. Ship your mag release to:
MaddMacs Precision Tactical, LLC
2401 Beaverdale Rd NE
Dalton, GA 30721
Include a copy of the order receipt you received by email
You can also send your frame (lower) to have the mag release removed then re-installed once button is installed. Additional cost will apply.
$50.00
(Price does NOT include return shipping)
**NOTE** This is a permanent modification to your mag release. Button will be permanent. View photo of installed extended magazine release below.
MaddMacs 22/45™ Extended Bolt Knob #2245EBK1
Extended bolt knob for easier cycling of the bolt. NO MORE! pinched fingers. Threaded at 5/16-18. Black Oxide. Will work with any MK Series pistols.
**Gunsmithing installation required** NO returns excepted
$42.95
**Gunsmithing installation required** NO returns excepted
$42.95
Installation #2245EBK1I
MaddMacs can install the extended bolt knob to your bolt. The cost includes installation fee and knob. Ship your bolt to:
MaddMacs Precision Tactical, LLC
2401 Beaverdale Rd NE
Dalton, GA 30721
Include a copy of the order receipt you received by email
$125.00
(price does NOT include return shipping)
**NOTE** This is a permanent modification to your bolt. Knob will be permanent.
Installed extended mag release
|
Installed extended bolt knob
|
If you have any questions or need more information about the products shown above, please contact Jason at jajones@maddmacsprecisiontactical.com.
Volquartsen Accurizing Kit #MPT3AK3B
Complete drop-in kit comes complete with Target Hammer, Target Sear, Target Trigger (available in either black hard anodized aluminum or optional stainless steel), Extended Bolt Release and Trigger Return Spring with Polished Plunger. The trigger features adjustable pretravel and overtravel screws. The Accurizing Kit combines all of the internal components needed for that crisp, clean 2.25lb trigger pull the discriminating shooter is looking for. No stoning or fitting required. Final trigger pull may vary slightly due to factory frame variances.
Fits the Ruger® MKII™, MKIII™ and MKIII™ 22/45™ (extended bolt release is not used when installing in a 22/45).
Option for MKIV™ accurizing kit after clicking Buy Now
$139.95 Accurizing Kit Only
Fits the Ruger® MKII™, MKIII™ and MKIII™ 22/45™ (extended bolt release is not used when installing in a 22/45).
Option for MKIV™ accurizing kit after clicking Buy Now
$139.95 Accurizing Kit Only
Installation #MPT3AK3BI
MaddMacs can install your Volquartsen Accurizing Kit. There is no need to take it to a gunsmith, simply send us your frame with mainspring assembly via USPS Priority Mail. Price includes Accurizing Kit, MaddMacs Stainless Steel hammer bushing, reduced hammer spring and complete installation. Does NOT include return shipping.
Ship your frame and mainspring assembly to:
MaddMacs Precision Tactical, LLC
2401 Beaverdale Rd NE
Dalton, GA 30721
Include a copy of the order receipt you received by email
$200.00
Volquartsen Competition Bolt #MPTVC3BT
The Competition Bolt is CNC-machined and ground for superior tolerances, fit and finish. It features an Exact Edge Extractor as well as the SureStrike Firing Pin.
$298.95
$298.95
volquartsen 22/45 Target frame #MPTVCTF
The VC 22/45™ Target Frame is CNC-machined from aluminum alloy. It is a complete frame with the following features: Accurizing Kit (includes Extended Bolt Release, CNC-machined Target Trigger, wire EDM-cut Target Hammer and Target Sear), CNC-Machined Disconnector and Extended Safety. The VC Frame is shipped with a clean, crisp 2.25lb trigger pull. The magazine disconnect has also been eliminated from this frame.
Color options - Black Only at this time
$549.95
Color options - Black Only at this time
$549.95
Volquartsen 22/45 Mainspring Assembly #MPTVCMS
Complete mainspring assembly designed for the Ruger MKII™ or MKIII™ 22/45™. Mainspring components are wire EDM-cut and CNC-machined.
The VC mainspring does not feature the lock feature found on the Ruger® factory MKIII™ Mainspring.
*Available in Black or SS*
Material option available after clicking "Buy Now"
$79.95
The VC mainspring does not feature the lock feature found on the Ruger® factory MKIII™ Mainspring.
*Available in Black or SS*
Material option available after clicking "Buy Now"
$79.95
Torx Grip Screws #MPTTXGSB
Miniature star shape adds that distinctive, personal touch to your 22/45. Machined and hardened screws fit flush in all factory and aftermarket 22/45™ grip panels.
Color: Blued
$22.95
Color: Blued
$22.95
Torx Grip Screws #MPTTGSS
Miniature star shape adds that distinctive, personal touch to your 22/45™. Machined and hardened screws fit flush in all factory and aftermarket 22/45™ grip panels.
Color: Stainless Steel
$24.95
Color: Stainless Steel
$24.95